RoboSavvy Forum

[SOLVED] No Comms at all

2010-09-28T10:31:06+01:00

So i can put this one to bed , all sorted with a new rbc and i found a broken lead on one leg that was giving an error code . Works 100% , has good software and is ideal for the newbies out there !

Statistics: Posted by rep001 — Tue Sep 28, 2010 10:31 am

[SOLVED] No Comms at all

2010-09-08T14:39:10+01:00

Yep so you are were I am , confused and still in need of some help !
It is indeed a robobuilder !!!!

Statistics: Posted by rep001 — Wed Sep 08, 2010 2:39 pm

[SOLVED] No Comms at all

2010-09-07T19:47:05+01:00

rep001 wrote:
Note it says ROBONOVA !

ROBONOVA !!! It's a joke You are here in Robobuilder Section

Statistics: Posted by Flid — Tue Sep 07, 2010 7:47 pm

[SOLVED] No Comms at all

2010-09-07T17:31:31+01:00

Other than the reset button on the back is there any other form of harder reset without a response from the rcb. All files i try to upload FAIL.

Statistics: Posted by rep001 — Tue Sep 07, 2010 5:31 pm

[SOLVED] No Comms at all

2010-09-06T20:39:00+01:00

Note it says ROBONOVA !

Statistics: Posted by rep001 — Mon Sep 06, 2010 8:39 pm

[SOLVED] No Comms at all

2010-09-06T20:37:54+01:00

ok i have managed to get the com port to stay open but still cannot connect . I have tried to install a hex test file but get the message FAIL. cannot comunicate in any way as i do not understand Putty. Strangely when i press the red Stand and greet button on the remote it speaks 'Hello my name is ROBONOVA' ? then the red error light starts flashing.
What am i doing..................

Statistics: Posted by rep001 — Mon Sep 06, 2010 8:37 pm

[SOLVED] No Comms at all

2010-09-06T19:40:03+01:00

So no comms at all - not even firmware updates, that sounds like more of a hardware problem. The only things to check are the connection to the RBC unit.

What lights are showing on it when switched on ?

Are you using a USB->COM converter - or direct from PC ?

If you connect Putty and open and then switch on the unit - do you see a ^ character sent ?

cheers

Statistics: Posted by l3v3rz — Mon Sep 06, 2010 7:40 pm

[SOLVED] No Comms at all

2010-09-06T17:36:01+01:00

Hi thanks for that, the port is 100% available. I occasionally get the error message No Ack if that helps. I cannot upgrade software as i have no Com.

Statistics: Posted by rep001 — Mon Sep 06, 2010 5:36 pm

[SOLVED] No Comms at all

2010-09-05T19:24:19+01:00

Are you sure that you port com is free and not used by another software ?

Try with hyperterminal or Putty to see the potential error

Statistics: Posted by Flid — Sun Sep 05, 2010 7:24 pm

[SOLVED] No Comms at all

2010-09-05T17:24:40+01:00

Have a look at this thread. You can see some things tried in the past

http://robosavvy.com/forum/viewtopic.php?p=26011

Have you tried up loading recent firmware such as 2.30 and are you using v1.32 of the motion software ?

Statistics: Posted by l3v3rz — Sun Sep 05, 2010 5:24 pm

[SOLVED] No Comms at all

2010-09-05T14:59:45+01:00

Yes thanks but tried that already, just no response at all.

Statistics: Posted by rep001 — Sun Sep 05, 2010 2:59 pm

[SOLVED] No Comms at all

2010-09-05T13:49:47+01:00

I think this is sounds like problem other people have had. Make sure your rbc is in PC control mode (hold PF2 down at power up) You should have blue and orange lights on. Now connect - baud rate is 115200.

Statistics: Posted by l3v3rz — Sun Sep 05, 2010 1:49 pm

Help needed

2010-09-05T11:10:10+01:00

I am still having the same issue. i cannot get the pc to talk with the RBC at all. I have tried all versions of Motionbuilder and simply cannot open the port >
The port is fine on my pc as i use the same port and lead for a Bioloid.
I really do want to crack on with some motions so if anyone has any idea.....

Statistics: Posted by rep001 — Sun Sep 05, 2010 11:10 am

[SOLVED] No Comms at all

2010-09-04T22:32:44+01:00

Need your help folks, 5720 will not keep a port open. Using motionbuilder or any others i select my com it opens and goes green for a second then switches to closed red. I cannot contact at all not even a firmware update. At a loss as to my next step , any thoughts please.............. ?

Statistics: Posted by rep001 — Sat Sep 04, 2010 10:32 pm