RoboSavvy Forum

Help, RoboBuilder Error

2011-08-17T18:18:30+01:00

l3v3rz wrote:
What version of the firmware are you using ?

I have installed almost all the firware, but I think the firware not overwrite the entire memory, I sent a message to robobuilder, I am waiting for reply,,,

Statistics: Posted by Ramos Darias — Wed Aug 17, 2011 6:18 pm

Help, RoboBuilder Error

2011-08-17T18:13:50+01:00

I have installed almost all the firware, but I think the firware not overwrite the entire memory, I sent a message to robobuilder, I am waiting for reply,,,

Statistics: Posted by Ramos Darias — Wed Aug 17, 2011 6:13 pm

Help, RoboBuilder Error

2011-08-17T13:55:13+01:00

What version of the firmware are you using ?

Statistics: Posted by l3v3rz — Wed Aug 17, 2011 1:55 pm

Help, RoboBuilder Error

2011-08-16T21:35:54+01:00

Then you have the same problem robobuilder Kondo, the problem is in communication with the controller servos, and have reviewed the connection is direct between the terminals and the servo and everything is perfect. I think it is a matter of piece of memory that is not updated with the firware or broken cpu

Statistics: Posted by Ramos Darias — Tue Aug 16, 2011 9:35 pm

Help, RoboBuilder Error

2011-08-16T20:18:19+01:00

i checked the serial cable and the pc connection and its work without any problem, I'm sure the problem is with the bootloader or something else in the robot,
if you have any suggestions how to recover this problem and roll it back to the time the bootloader of the robot work well i will be glad for some help here.
thank you

Statistics: Posted by Ben Rubi — Tue Aug 16, 2011 8:18 pm

Help, RoboBuilder Error

2011-08-12T22:44:16+01:00

hello, kondo has happened to me the robobuilder for me to look, I've done what you are speaking and communication with the controller max232 working properly, I tested the max232 input and output and perfect, but a strange problem I do not detect the servos, can tell me +V the terminals of the servo¿?

Statistics: Posted by Ramos Darias — Fri Aug 12, 2011 10:44 pm

Help, RoboBuilder Error

2011-08-09T13:11:27+01:00

If it is a comms problem, then since you see the "^" it must be one way.

To check cable short the tip and middle ring of jack plug. Should echo characters back.
Check the jack socket on RBC is not damaged.
If you have Bluetooth, temporarily remove it.

Statistics: Posted by i-Bot — Tue Aug 09, 2011 1:11 pm

Help, RoboBuilder Error

2011-08-07T18:24:09+01:00

if you can't run the RBCupgrade tool - sounds like you have a comms problem between PC and RBC. Check hardware connections, check you have the right port and try turning robot/RBC on and off several times. Sometimes it take 2-3 power cycles before it starts.

Statistics: Posted by l3v3rz — Sun Aug 07, 2011 6:24 pm

Help, RoboBuilder Error

2011-08-06T21:19:15+01:00

when i use RBC upgrade tools and i push the reset button its writ to me no response from target bootloader.

Statistics: Posted by Ben Rubi — Sat Aug 06, 2011 9:19 pm

Help, RoboBuilder Error

2011-08-05T22:18:30+01:00

Ben - the basic.exe is a windows build of the firmware its not connected to the robot. It will talk to the simulator (if its running) but that's all - its to enable you to test out basic programs without a robot. You need to upload the .hex file to the robot using the RBCupload tool and then connect using a terminal emulator such as putty. See the wiki for details.

Statistics: Posted by l3v3rz — Fri Aug 05, 2011 10:18 pm

Help, RoboBuilder Error

2011-08-05T10:18:05+01:00

HELLO I THINK I HAVE THE SAME PROBLEM AND I DIDNT SUCCESS TO SOLVE IT.
i tried all kind of terminals and the robot is not communicated with the pc.
when i open the terminal i see the ^ symbol and its mean there is communication between the robot and pc.
when i use RBC upgrade tools and i push the reset button its writ to me no response from target bootloader.
and when i open the basic.exe from your site the screen is
Basic v=$Revision: 317 $
Commands: i r l c z q
WIN: servo read 0
.
.
.
WIN: servo read 20
20 servos connected
0 line in memory
win: suond init
win : sampl sound 1?

can you help me to solve this probleam, and make the robot works as needed?[/img]

Statistics: Posted by Ben Rubi — Fri Aug 05, 2011 10:18 am

Help, RoboBuilder Error

2011-07-28T22:55:40+01:00

Video Error:

http://www.youtube.com/v/aOgftoqWZnY

Photo motherboard

http://imageshack.us/g/21/86497051.jpg/

Statistics: Posted by Kondo — Thu Jul 28, 2011 10:55 pm

Help, RoboBuilder Error

2011-07-26T14:21:56+01:00

Thanks for your help, but I have not done anything for the moment

Statistics: Posted by Kondo — Tue Jul 26, 2011 2:21 pm

Help, RoboBuilder Error

2011-07-25T11:05:40+01:00

ok - its really very simple and if you do want to give it a try later see the wiki for details:

http://code.google.com/p/robobuilderlib/wiki/Basic

hope you can sort you problem out

good luck -

Statistics: Posted by l3v3rz — Mon Jul 25, 2011 11:05 am

Help, RoboBuilder Error

2011-07-25T00:46:00+01:00

I think this test is beyond my knowledge and I do not get both, but I appreciate your help, I begin to think that my robot controller died: (

Statistics: Posted by Kondo — Mon Jul 25, 2011 12:46 am