RoboSavvy Forum

Re: Havimo 2.0 Error Capture Image!

2014-05-05T04:30:30+01:00

i am not very familar with image capturing software, so i searched the web and find the following things are mattered while you are capturing image with camera: twain scanning basic acquisition and twain scanning device control.

Statistics: Posted by gdjump — Mon May 05, 2014 4:30 am

Havimo 2.0 Error Capture Image!

2013-06-05T03:10:24+01:00

your module isn't have a problem, check your camera beforecapturing an image c# .maybe something needs to be updated so that it can work normally.

Statistics: Posted by dtimage — Wed Jun 05, 2013 3:10 am

Havimo 2.0 Error Capture Image!

2012-05-16T08:54:19+01:00

Mr.Hamid...

i have to try the reset to factory defaults and try setting auto exposure in camera settings not happen error at device..
when auto exposure ,the slider is move up and down if the camera is moving..

this is the picture of setting default and auto exposure,,,

Mr.hamid,would you mind if you give me the circuit electronic of havimo2 ?.
i want to repair the hardware...
teach me to repair it sir...
i hope the havimo not broken...

what kind of chip in this hardware ?.and what is the content of atmega8 in this havimo2 ?.
would you mind if you can send the file at my email sir ?.
this is my email ari_th3b3st16@yahoo.co.id

thanks a lot of sir...

Statistics: Posted by ari_th3b3st — Wed May 16, 2012 8:54 am

Havimo 2.0 Error Capture Image!

2012-05-07T15:08:18+01:00

Hi,

did the reset to factory defaults work without errors? try setting auto exposure in camera settings and check if the exposure slider moves when you cover the camera. report me the results and I can say if there is any problems with the camera chip.

Best regards,
Hamid.

Statistics: Posted by hamid_m — Mon May 07, 2012 3:08 pm

Havimo 2.0 Error Capture Image!

2012-05-07T14:31:32+01:00

Mr. hamid...

I still cannot use this Havimo2...
give me the other clue about it...

thanks...
Regards

Statistics: Posted by ari_th3b3st — Mon May 07, 2012 2:31 pm

Havimo 2.0 Error Capture Image!

2012-05-03T11:19:28+01:00

Hi,

I don't think that your module has a hardware problem. It may be with the settings. also try resetting to factory defaults (availabe in HaViMo GUI) and try again.

Best regards,
Hamid.

Statistics: Posted by hamid_m — Thu May 03, 2012 11:19 am

Havimo 2.0 Error Capture Image!

2012-05-03T04:52:26+01:00

Mr.hamid..

this is code from hyperterminal or terminal of robotis communication.

"<[ "ERROR : 8100 : 0064 : 02"]>"

when i play the cm-510,so print out of coding havimo2 in terminal communication serial like as it,,,
what happen about my havimo2 ?.

thanks a lot of with your help sir...

Statistics: Posted by ari_th3b3st — Thu May 03, 2012 4:52 am

Havimo 2.0 Error Capture Image!

2012-05-01T16:02:44+01:00

Mr.hamid,,,

I`m sorry sir...
i mean the status is "Havimo2 Found"...
this is my wiring and hardware of havimo cm-510..
please help me sir...
i hope this devicce not broken,,,

sir...i dont know how to insert the image...
if i give you url image in facebook,
would you to open this image sir ?.

Statistics: Posted by ari_th3b3st — Tue May 01, 2012 4:02 pm

Havimo 2.0 Error Capture Image!

2012-05-01T07:40:24+01:00

Hi,

are you sure you have
"Havimo Found"

and not
"HaViMo2 Found" ?

which product are you using? can you post a photo of your Harware setup, I think this helps finding the problem.

Best regards,
Hamid.

Statistics: Posted by hamid_m — Tue May 01, 2012 7:40 am

Havimo 2.0 Error Capture Image!

2012-05-01T02:19:57+01:00

Mr. hamid ..,
I've already done that ...
A. My antivirus is disabled
2. firewall of OS I have off ..
3. I have selected the 'MANAGE' in board of CM-510
4. i`m click check camera and status have "Havimo Found" in HavimoGUI
but i still can not capture the image ...
please help me Mr.hamid...
Have my havimo is broken ?.
thanks a lot of,,give me advice about it...

Statistics: Posted by ari_th3b3st — Tue May 01, 2012 2:19 am

Havimo 2.0 Error Capture Image!

2012-04-24T11:06:45+01:00

Hi,

Calib.hex is out-dated. The only thing you should do when connecting via CM5/510 ist to set the controller in "MANAGE" mode, so that the LED blinks. After connecting to the board the LED stops blinking.
You can also check the camera before capturing an image.

Best regards,
Hamid.

Statistics: Posted by hamid_m — Tue Apr 24, 2012 11:06 am

Havimo 2.0 Error Capture Image!

2012-04-13T17:42:06+01:00

Mr. Hamid,,,
I have a problem with my 2.0 havimo ..
I use usb2dynamixel-510 >> cm >> havimo track to calibrate the color to be used,,
in havimo_GUI_3, after selecting == cm-510 communication port and I use.
I select a camera check, then I click the sample image,,
emerging status "Image Capture Error",,,
I use OS win_xp, and I use roboplus.
are havimo mine broken?.
is the procedure that I use one?.
is it necessary to havimo 2.0 firmware calib.hex?
Please help pak hamid ...
thank you very much for your help ..
sorry,my language is not good...
Ari

Statistics: Posted by ari_th3b3st — Fri Apr 13, 2012 5:42 pm