RoboSavvy Forum

Autonomous RN1 or Spare Head 2

2006-05-08T12:32:57+01:00

Excellent -

have you put some sort of sensor onto your servo? Do you plan too?

Would love to see what your new Head for RN1 looks like

Pev

Statistics: Posted by Pev — Mon May 08, 2006 12:32 pm

Autonomous RN1 or Spare Head 2

2006-05-08T07:03:56+01:00

I got it working, thanks so much. It was the Delay command, just like you pointed out.

Statistics: Posted by H3dude — Mon May 08, 2006 7:03 am

Re: Autonomous RN1 or Spare Head 2

2006-05-05T17:56:32+01:00

Pev wrote:
Looking at your code you have the additional servo plugged into port 11, but your not calling your head_turn_no routine in the code snippet you have posted.

I am calling it from a remocon button press, I just didn't include it in my post.

The DELAY command however, is most likely the solution as I'm using the same servo (s3004) as you. I'll try that now. Thanks for your help!

Statistics: Posted by H3dude — Fri May 05, 2006 5:56 pm

Re: Autonomous RN1 or Spare Head 2

2006-05-05T07:29:38+01:00

H3dude wrote:
Pev wrote:The servo is attached to port 9 and accessed using the servo command, format SERVO 9, {degree} where {degree} is a value from 10 to 190.

Pev, this syntax doesn't seem to do anything in my standard pose block nor in my zero settings:

standard_pose:
SERVO 11, 98
MOVE G6A, 100, 76, 145, 93, 100, 100
MOVE G6D, 100, 76, 145, 93, 100, 100
MOVE G6B, 100, 30, 80, 100, 100, 100
MOVE G6C, 100, 30, 80, 100, 100, 100
WAIT
RETURN

I also tried a simple move

head_turn_no:
SPEED 5
SERVO 11,98
SERVO 11,30
SERVO 11,160
SERVO 11,98
GOSUB standard_pose
RETURN

alas, again I am clueless. Any ideas?

Hi,

Looking at your code you have the additional servo plugged into port 11, but your not calling your head_turn_no routine in the code snippet you have posted. If you want him to turn his head every time he enters standard pose I'd go for something like this:

standard_pose:
SERVO 11, 98
MOVE G6A, 100, 76, 145, 93, 100, 100
MOVE G6D, 100, 76, 145, 93, 100, 100
MOVE G6B, 100, 30, 80, 100, 100, 100
MOVE G6C, 100, 30, 80, 100, 100, 100
WAIT
GOSUB head_turn_no
RETURN

head_turn_no:
SPEED 5
SERVO 11,98
deley 500
SERVO 11,30
delay 500
SERVO 11,160
delay 1000
SERVO 11,98
delay 500
RETURN

I've added the delays just to ensure that servo has time to move. I was using a standard non-digital non feedback servo so if I wasn't careful the servo didn't move as it never had time to.

Hope this makes sense

Pev

PS - if it helps when I was using the sharp IR sensor attached to AD port 1 I used the following code to move the head servo and check the sensor:

SERVO 9, 30 'move head servo to left position
DELAY 3000
LEFT = AD(1)'Read Sonar on Sonar Port 5

'Check Right
SERVO 9, 190 'move head servo to right position
DELAY 4000
RIGHT = AD(1)

SERVO 9, 108 'move head to center position
DELAY 1000

So he looked left and checked the sesor then looked right and checked the sensor.

Statistics: Posted by Pev — Fri May 05, 2006 7:29 am

Re: Autonomous RN1 or Spare Head 2

2006-05-04T10:46:10+01:00

Pev wrote:
The servo is attached to port 9 and accessed using the servo command, format SERVO 9, {degree} where {degree} is a value from 10 to 190.

Pev, this syntax doesn't seem to do anything in my standard pose block nor in my zero settings:

standard_pose:
SERVO 11, 98
MOVE G6A, 100, 76, 145, 93, 100, 100
MOVE G6D, 100, 76, 145, 93, 100, 100
MOVE G6B, 100, 30, 80, 100, 100, 100
MOVE G6C, 100, 30, 80, 100, 100, 100
WAIT
RETURN

I also tried a simple move

head_turn_no:
SPEED 5
SERVO 11,98
SERVO 11,30
SERVO 11,160
SERVO 11,98
GOSUB standard_pose
RETURN

alas, again I am clueless. Any ideas?

Statistics: Posted by H3dude — Thu May 04, 2006 10:46 am

Autonomous RN1 or Spare Head 2

2006-03-26T19:06:05+01:00

With the following source code the sonar is working, and printing is also possible.

But the measured distance isn't correct.

I think the sonar() command is only working if the echoline is high when (before) sonar() is executed.

For details have look on http://robosavvy.com/Builders/ucrobots/
file: srf04-diagnostic.doc

================================
dim a as integer
LCDINIT

main:
a = sonar(5)
a = sonar(5)
delay 100

if a=0 then goto main

print "SONAR(5): "
print format(a, dec)
print 10, 13

goto main

Statistics: Posted by ucrobots — Sun Mar 26, 2006 7:06 pm

Autonomous RN1 or Spare Head 2

2006-03-25T22:24:17+01:00

I tried the source code below.
With this code the sonar is working and the LED is blinking.

But the measured distance isn't correct.

delay a takes about 700ms, this means a=700 and distance = 700mm.
But the real distance was about 190cm.

For details have look on http://robosavvy.com/Builders/ucrobots/
file: srf04-diagnostic.doc

================================
dim a as integer

10:

a = sonar(5)
out 52,0
out 9,0
delay a

a = sonar(5)
out 52,1
out 9,1
delay a
goto 10

'===================================

Statistics: Posted by ucrobots — Sat Mar 25, 2006 10:24 pm

Testing SRF04

2006-03-25T22:39:33+01:00

Today I found this message on the Hitec support page :

Please check the trigger and echo pins are connected correctly.
If it is connected to port combination 0, as manual describes, then
with the following source code, you can check if sonar does the job.
In case it works, then head LED will blink.

'================================

dim a a s integer

10:

a = sonar(0)
out 52,0
out 8,0
delay a

a = sonar(0)
out 52,1
out 8,1
delay a

goto 10
'===================================

Statistics: Posted by ucrobots — Sat Mar 25, 2006 4:20 pm

Autonomous RN1 or Spare Head 2

2006-03-24T22:45:07+01:00

Yeah they are discontinuing it that is why it is 50% off at the stores, not the websites.

Statistics: Posted by RubikCube — Fri Mar 24, 2006 10:45 pm

Autonomous RN1 or Spare Head 2

2006-03-24T19:44:37+01:00

Radioshack has dis-continued the Vex line due to poor sales. It's turning into a cell phone store with over-priced "universal" chargers.

Statistics: Posted by subpilot — Fri Mar 24, 2006 7:44 pm

Autonomous RN1 or Spare Head 2

2006-03-24T18:01:48+01:00

Got the following from Hitec/Multiplex, hope you find it useful:

Regarding Sonar, the pin connection on the manual is described invertedly.
Trigger and echo should be changed. The second issue is the delay time.
We will put the test source on our download site.

Statistics: Posted by robosavvy — Fri Mar 24, 2006 6:01 pm

Autonomous RN1 or Spare Head 2

2006-03-24T16:32:55+01:00

ucrobots,

I don't know if you know this already, let me try to explain what is happening to your code. ROBOBASIC is not a fully synchronous language, if you read the explanation of WAIT statement, you coud conclude that some of the commands in ROBOBASIC does not wait for the previous command to finish before it executes the next one. So on your code below SONAR comand will execute before SONAR finishes the PRINT command will be executed as well. That is why your readings are inconsistent or better yet always zero. You also need to give SRF04 time to process the bounced ping if you listen to your SRF04, and it is ticking very fast you might want to slow it down with DELAY=500

DIM I AS BYTE
DIM B AS INTEGER

PTP SETON
PTP ALLON

'============================
MAIN:

TEMPO 230
MUSIC "o23ggaagg"
DELAY 1000

MOTOR 6
MOTOR 8
MOTOR 9

LCDINIT

loop1:

A = AD(6)
wait
I = I+1

L2:
DELAY 50
Increase your delay

B = SONAR(5) 'SRF04
put a WAIT here

'IF B = 0 THEN GOTO L2

PRINT "Analog Input 6: "
put a WAIT here
PRINT FORMAT(A, DEC)
put a WAIT here
PRINT "Sonar(5): "
put a WAIT here
PRINT FORMAT(B, DEC)
put a WAIT here
PRINT " I= "
put a WAIT here
PRINT FORMAT(I, DEC)
put a WAIT here

PRINT 13, 10

GOTO loop1
GOTO MAIN

Statistics: Posted by RubikCube — Fri Mar 24, 2006 4:32 pm

Autonomous RN1 or Spare Head 2

2006-03-24T14:50:19+01:00

Thanks for the tip Subpilot.

I see you are from California. Did you know that you can buy the Vex ultrasonic sonar sensor from RadioSahck for $19.00 and it will work the same way as the SRF04?

Just connect sonar sensor input to MRC-3024 output port and sonar output to MRC-3024 input. It worked for me.

Firmware Version is 2.5

Statistics: Posted by RubikCube — Fri Mar 24, 2006 2:50 pm

Autonomous RN1 or Spare Head 2

2006-03-24T09:33:22+01:00

My sonar does not work. The SFR04 is realy ok.
I tried all your tips but with no succsess.

Another funny thing is that SONAR(8) does not generate any triggerpulse on Port#16, but PULSE(16) does.

So what Firmware version do you have ?

Statistics: Posted by ucrobots — Fri Mar 24, 2006 9:33 am

Autonomous RN1 or Spare Head 2

2006-03-24T05:50:01+01:00

I found that my sonar does work. I was an idiot and was using a Byte varible while the sonar sub spits out integers.
Rubic, I am also using the etx command to send data over my Bluetooth link. Rather than divide the value by 64 and lose resolution, you could right shift by 8 to get the upper byte.

a16 = SONAR(5)
ETX 9600,a16 ' Sends lower byte
a16=a16>>8
ETX 9600,a16 ' Sends upper byte

Statistics: Posted by subpilot — Fri Mar 24, 2006 5:50 am