RoboSavvy Forum

MOVEPOS command syntax

2008-08-05T18:51:57+01:00

Thank you.
Strangely enough it compiles for me now!!!
Ran the editor.
Pasted your code into a new page, it compiled.
Loaded my old page and it now compiles.
All I have done is close the editor and reopen it!!!
At least out of this I found the Japanese WIKI pages for RN.
David

Statistics: Posted by robots42 — Tue Aug 05, 2008 6:51 pm

MOVEPOS command syntax

2008-08-05T18:14:06+01:00

The following compiles and works for me on version 2.5.61

Code:: K1_PZERO: MOVEPOS G24,Pzero WAIT GOTO K1_PZERO Pzero: POS G24,100,76,144,96,101,100,101,30,81,100,100,100,101,30,81,100,100,100,100,76,144,96,101,100

It make this byte code which looks good:

Code:: 0x10 MOVEPOS [ 0x17] 0x13 WAIT 0x14 GOTO [ 0x10] 0x17 POS 0, 24, 100, 76, 144, 96, 101, 100, 101, 30, 81, 100, 100, 100, 101, 30, 81, 100, 100, 100, 100, 76, 144, 96, 101, 100, 0x32 GOTO [ 0x32]

Statistics: Posted by i-Bot — Tue Aug 05, 2008 6:14 pm

MOVEPOS command syntax

2008-08-05T17:55:08+01:00

Thank you for replying but with or without G24, and or commas, it still gives
Error 23 : [MOVEPOS] Wrong command syntax.
ie

Code:: 'these all produce Error 23 MOVEPOS Pzero MOVEPOS G24, Pzero MOVEPOS, G24, Pzero MOVEPOS POS Pzero MOVEPOS MOVE Pzero MOVEPOS MOVE24 Pzero MOVEPOS (Pzero) MOVEPOS =Pzero ' MOVEPOS [Pzero] 'gives Error 1 MOVEPOS {Pzero} 'gives Error 1

yu1rou1 on blog.livedoor.jp also commented on this but I can't find any answer.
http://blog.livedoor.jp/yu1rou1/
[Janglish]
November 23, 2005
POS command and the command MOVEPOS

ROBOBASI new manual has been published. Why Word files…
Certainly not read, but I did not think that most people are usually text or pdf I guess I am.

Why, I had read the POS command and the command MOVEPOS found. According to the manual servo POS command pre-specified angle

to them, MOVEPOS the position to call at any time to MONORASHII. I immediately tried.

Error 23 : [MOVEPOS] Wrong command syntax.

RAM;. Command from the manual, but I can not cut and paste. By the way

POS01: POS G6A, 10, 32, 15, 120, 78, 93

Is not an error, but

GOTO POS01

The command passes without problems. Rather than simply re-caret misspelling, or not available at this time for me to

announce that.
[/Janglish]

David

Statistics: Posted by robots42 — Tue Aug 05, 2008 5:55 pm

MOVEPOS command syntax

2008-08-05T15:48:53+01:00

Try it with G24 in the MOVEPOS too. Like this

Code:: K1_PZERO: MOVEPOS G24, Pzero WAIT GOTO GetCmnd Pzero: POS G24,100,76,144,96,101,100,101,30,81,100,100,100,101,30,81,100,100,100,100,76,144,96,101,100

Statistics: Posted by i-Bot — Tue Aug 05, 2008 3:48 pm

MOVEPOS command syntax

2008-08-05T13:15:00+01:00

Has anybody used MOVEPOS ?
What is the correct command syntax?

Code:: K1_PZERO: MOVEPOS Pzero WAIT GOTO GetCmnd Pzero: POS G24,100,76,144,96,101,100,101,30,81,100,100,100,101,30,81,100,100,100,100,76,144,96,101,100

This gives a command syntax error at MOVEPOS Pzero
to me it appears to be exactly as in the manual p93
(don't ask me why here there is a huge space before POS)
Help would be appreciated.
David

Statistics: Posted by robots42 — Tue Aug 05, 2008 1:15 pm