RoboSavvy Forum Robosavvy Forum: The largest online community of Humanoid Robot Builders 2008-06-09T10:18:49+01:00 http://forum.robosavvy.com/feed.php?f=5&t=2610 2008-06-09T10:18:49+01:00 2008-06-09T10:18:49+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16274#p16274 <![CDATA[Problems with flashing the cm5]]>
no with PROGRAM, i meen a compiled program for the ATMega128 (hex-file).
I now used the Robot-Terminal to upload the program.
It works well, like it did before. It turned out that the only problem was that the the program I loaded did not light up the leds so all the time it was working correct but I didn't notice :-(

Sorry, I bothered you with that.


best regards,
Alex

Statistics: Posted by sirhoop — Mon Jun 09, 2008 10:18 am

]]> 2008-06-05T15:37:11+01:00 2008-06-05T15:37:11+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16224#p16224 <![CDATA[Re: Problems with flashing the cm5]]>
sirhoop wrote:
Hello,
I want to load another program on the cm5. For that purpose I used the Update-function of the BehaviourControl Programmer of Robotis.
Unfortunately I always end up getting an ErrorMessage.
"You failed cm5-update!
You need to install cm5-program refering to bioloid-user guide."
Then I need to recover it using the bootloader. I tested it with several programs.
Is there another way of getting my own program on the cm5?
best regards,
Alex
Wait a minute. You're trying to upload a program (.bpg file) via update, as in BehaviorControlProgrammer > Management > Update CM-5? That's not going to work.

Statistics: Posted by AlphA — Thu Jun 05, 2008 3:37 pm

]]> 2008-06-04T07:38:23+01:00 2008-06-04T07:38:23+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16187#p16187 <![CDATA[Re: Problems with flashing the cm5]]>
Update utility makes some checks, dealing with the cm5 firmware, nothing else. (but try with an original one... to check if bootloader is not dammaged)

Statistics: Posted by le fatumbi — Wed Jun 04, 2008 7:38 am

]]> 2008-06-03T16:56:29+01:00 2008-06-03T16:56:29+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16174#p16174 <![CDATA[Re: Problems with flashing the cm5]]>
sirhoop wrote:
...Then I need to recover it using the bootloader. I tested it with several programs. Is there another way of getting my own program on the cm5?


It is highly unlikely that your bootloader is damaged. Have you tried the robot-terminal interface ? it is well documented in the manual.

Statistics: Posted by limor — Tue Jun 03, 2008 4:56 pm

]]> 2008-06-03T14:00:20+01:00 2008-06-03T14:00:20+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16154#p16154 <![CDATA[Problems with flashing the cm5]]> Statistics: Posted by StuartL — Tue Jun 03, 2008 2:00 pm

]]> 2008-06-03T10:34:35+01:00 2008-06-03T10:34:35+01:00 http://forum.robosavvy.com/viewtopic.php?t=2610&p=16140#p16140 <![CDATA[Problems with flashing the cm5]]>
I want to load another program on the cm5. For that purpose I used the Update-function of the BehaviourControl Programmer of Robotis.

Unfortunately I always end up getting an ErrorMessage.

"You failed cm5-update!
You need to install cm5-program refering to bioloid-user guide."

Then I need to recover it using the bootloader. I tested it with several programs.

Is there another way of getting my own program on the cm5?

best regards,
Alex

Statistics: Posted by sirhoop — Tue Jun 03, 2008 10:34 am

]]>