RoboSavvy Forum

RC servo on Bioloid bus.

2009-11-30T07:46:38+01:00

Excellent video.Got it working is good.

Fog Light

Statistics: Posted by PeterKesel — Mon Nov 30, 2009 7:46 am

RC servo on Bioloid bus.

2009-11-30T04:40:23+01:00

More progress.

phpBB [media]

Here's the camera test tsk..
http://www.mediafire.com/?sharekey=e01a ... 8345cbe4ce

Statistics: Posted by billyzelsnack — Mon Nov 30, 2009 4:40 am

RC servo on Bioloid bus.

2009-11-29T00:08:41+01:00

Phfeww. Got it working.

http://www.mediafire.com/?sharekey=e01a ... af670496da

Looks like some of the other bioloid-io code that I was not using was messing with the pins ( as it's supposed to!) I just commented all the original functionality out and its working even when a motionpage is set now.

phpBB [media]

Statistics: Posted by billyzelsnack — Sun Nov 29, 2009 12:08 am

RC servo on Bioloid bus.

2009-11-28T04:59:04+01:00

phpBB [media]

I've run into a hitch. As soon as a motionpage is set I can no longer communicate with my board. I'm not sure why. I wonder if I need to do my work inside the callback.

Update: Nope. Looks like you can only do reads inside a callback.

Update2: So it looks like I can write to AX-12's after a motionpage load so I have no idea why I can't write to my board after a motionpage load. Anybody have ideas?

Statistics: Posted by billyzelsnack — Sat Nov 28, 2009 4:59 am

RC servo on Bioloid bus.

2009-11-27T20:01:44+01:00

ok. I have two servos working now. Here's the code..

http://www.mediafire.com/?sharekey=e01a ... aacf568dab

Statistics: Posted by billyzelsnack — Fri Nov 27, 2009 8:01 pm

RC servo on Bioloid bus.

2009-11-27T18:07:31+01:00

I was working on the second servo last night, but my knowledge of cryptic avr timers is minimal. I hope to have it working today though. I'll post the code when it's done.

As far as interference with the IO. I dunno.

Statistics: Posted by billyzelsnack — Fri Nov 27, 2009 6:07 pm

Looks Good

2009-11-26T23:06:58+01:00

The code looks good. You updated the bioloid-io.c module to use the high resolution timer, added a new functions pwm_set and pwm_init to handle and set the servo and commented out the motor.c module. Folks will still need the rest of Jon and Davids Bioloid IO code from their repository.

I have been working on a generic IO board as well starting from the same code base. I appreciate you sussing out the settings for the 16bit timer. I had it on my list to sit down with the datasheet one of these days. I couldn't get close enough to 20ms with the low resolution timer.

Any problems with any of the other IO when you changed the timer? (I wouldn't expect it.) Any ideas on how to get the second servo working in this mode? Can you just use com1a1? Or is this out because of the high resolution timer? Maybe I will have to look at the datasheet after all, or go back to the 8 bit timer? I will give this a test over the weekend.

Thanks for this!
mmason

Statistics: Posted by profmason — Thu Nov 26, 2009 11:06 pm

RC servo on Bioloid bus.

2009-11-25T21:59:25+01:00

I modified Jon Hylands bioloid-io code to put a servo on the bus. He already did 99% of the code work for me so the changes were very small.

phpBB [media]

I just barely got this working, but I plan on adding support for two servo ( for my pan-tilt camera control ) as well as taking gyro and accel data and returning kalman filtered results. Funny enough the gyro and accel data will come from Jon's IMU. The CM-5 using roboplus task will read in the data from the IMU and then write that data to this device. The roboplus task will then read the results back. Kinda silly going back and forth like that, but roboplus task can't do any real math.

Here's the code..
http://www.mediafire.com/?sharekey=e01a ... 998cb4ca21

(here's the pan-tilt in action)

phpBB [media]

Statistics: Posted by billyzelsnack — Wed Nov 25, 2009 9:59 pm