RoboSavvy Forum

Help on RoboPlus

2010-03-26T18:45:23+01:00

Merlin wrote:
Do you know where I can get a PDF version of a Premium manual in order to guide me. The PDF help files I have found on Robotis site are very general, but not describe the actual building process of the differents models.

I'd think you should have received a build manual for the three humanoid robots with the Premium Upgrade Kit. If you didn't, perhaps let ROBOTIS know and I'm sure they will provide you with one.

I understand that ROBOTIS is working on a number of other robot configurations for the Premium Kit but am unsure of how they will distribute the build information once it's ready.

Harry

Statistics: Posted by HGM — Fri Mar 26, 2010 6:45 pm

Help on RoboPlus

2010-03-20T02:59:56+01:00

unfortunatly, i don't know where you can get a pdf version of the premium doc.
You may ask PedroR about it.
he seems to have good relationship with Robotis and they may satisfy your query...

Pero solo se trata de las 3 declinaciones del bipede en la documentacion.
para la piernas y los brazos, me parece ser lo mismo, solo el cuerpo es differente.
entiendo muy bien el espanol pero hace muy largo que no lo hablo.

salud
Fabian.

Statistics: Posted by FabinovX — Sat Mar 20, 2010 2:59 am

Help on RoboPlus

2010-03-19T22:26:34+01:00

Just today I have received the Upgrade Kit which will migrate my Comprehensive to Premium Kit.

I have a lot of doubts, some Software related and some others regarding the phisical building of the demo models described, which I have builded using the old CM-5 but not this new one. Even the plastic pieces are the same, the new Microprocessor and the LiPo battery are quite diferent from the old model and I can't figure out how to place together in one block.

Do you know where I can get a PDF version of a Premium manual in order to guide me. The PDF help files I have found on Robotis site are very general, but not describe the actual building process of the differents models.

Best regards

daniel

PS: Realmente puedes entender y escribir en español? sería fantástico...

Statistics: Posted by Merlin — Fri Mar 19, 2010 10:26 pm

Help on RoboPlus

2010-03-19T20:20:55+01:00

como quiera

Statistics: Posted by FabinovX — Fri Mar 19, 2010 8:20 pm

Help on RoboPlus

2010-03-19T20:18:59+01:00

I have a Comprehensive Kit which I am actually upgrading to Premium.
Even I was in robotics for a few years, I feel I am an eternal begginer on this area...
Regarding this particular issue, I remeber that in Behaviour Control Programmer(the old language for Bioloid) it was a sentence to setup the actuators in wheel or servo mode, I will search and share with you.
I hope you will stay on Roboplus for a while, so we can share progress and problems in the next future. And excuse moi, je ne parle pas le francais, ma langue maternelle est l'espagnol...so I prefer to speak in english for now.

Best regards

daniel

Statistics: Posted by Merlin — Fri Mar 19, 2010 8:18 pm

Help on RoboPlus

2010-03-19T19:55:20+01:00

Actually, i'm a beginner in robotics.
i bought my first robot at the beginning of february.
It's a Bioloid Premium so, Roboplus is for the moment the only way i know to program easily and quickly the robot, but i'm learning C++ and hope i will soon be able to program the bioloid this way.

Take care
FabinovX

ps : au fait, daniel, je suis français, alors si tu veux qu'on échange des tuyaux, va dans la section française du forum, ça sera plus simple pour nous deux !

Statistics: Posted by FabinovX — Fri Mar 19, 2010 7:55 pm

Help on RoboPlus

2010-03-19T17:25:39+01:00

Thanks you very much!! It's working now.

Are you trying the new Roboplus language as well?

Or only using the tools (Manager, Motion, Dynamixel, Terminal)?

daniel

Statistics: Posted by Merlin — Fri Mar 19, 2010 5:25 pm

Help on RoboPlus

2010-03-19T17:02:08+01:00

Ok, i'm at home now.
check this for each ID the code is trying to command :

if the actuator is set to 'joint', set it to 'wheel' then click 'APPLY'
It should work.

Cheers.
FabinovX

Statistics: Posted by FabinovX — Fri Mar 19, 2010 5:02 pm

Help on RoboPlus

2010-03-19T15:38:21+01:00

The fact is that is not my code...is the code from Robotis, so I guess this code has included the all sentences to work without any further action...finally is a demo code.
But aparently is not like that and the code is not running the motors. From Motion program the actuators runs Ok, the problem is on the Task Manager using the Obstacle Detection Car demo.
Thanks anyway

daniel

Statistics: Posted by Merlin — Fri Mar 19, 2010 3:38 pm

Help on RoboPlus

2010-03-19T09:31:01+01:00

Hello,
i didn't use endless turn for now but i think you need to use roboplus manager first.
Once connected to your CM5, go to each actuator you want to drive using endless turn.
I don't remember exactly where it is, but you can declare if you want to use your dynamixel as an endless turn device or not in one of the line of parameter.
Select each line and explore the menu on the right, you will find it for shure.
I think you can also do the declaration in your code once you have the right address value.

Cheers.
FabinovX

Statistics: Posted by FabinovX — Fri Mar 19, 2010 9:31 am

Help on RoboPlus

2010-03-18T21:50:08+01:00

Hi all,
I am trying the new Roboplus language with my Bioloid Comprehensive Kit based on CM-5 processor.
I have installed the last version of Roboplus SW, and also I have upgraded the CM-5 in order to be recognized by Roboplus.
All is going OK, so I started with a simple program example: Obstacle detection car, I guess many of you knows perfectly.
After I build the car, I have dowloaded to the demo program (from Robotis support site), the program runs Ok on the CM-5 but...the motors of the AX-12 doesn't run.
As far I understand, the sentence

ID [1]: Moving speed=CCW:500

will move the motor in one direction, while the sentence CW: 500 will move it on the other direction.

But the fact is the car doesn't move, even I am sure the program is actually running the Funtions involved, because I included some "debug" printing instructions and the Function is really executed.

Any suggestions? Is something missing on the demo program from Robotis?

Any help could be appreciated, thanks a lot

daniel

Statistics: Posted by Merlin — Thu Mar 18, 2010 9:50 pm