RoboSavvy Forum

great job

2013-05-23T09:04:22+01:00

you can reduce the head also by drilling two tiny holes on the backside motor.
you take part F3 AND DRILL THE MIDDLE HOLES THRU CASE OFF SERVO;
BOLT SIDES.the heat will stay hole day at 50.when servo is'n moving heat goes rapidly high,in 10 or 20 min you allreddy sit on yellow or red.
the temp trigger ,open manager llook for your servo and uncheck trigger there.

Statistics: Posted by nomad — Thu May 23, 2013 9:04 am

How Ax12+ detect Over-load ?

2013-05-20T06:44:45+01:00

After 1 year of struggle and lots of trials and different setups; I finally got success in Hacking Ax12+ Dynamixel. Yes; Its finally hacked
I have removed all the 4 tiny black gears and the tiny motor.
I have shutdown the overload trigger and Alarm LED from Dynamixel Wizard.
I have joined a 5amp 12volt Square shaped DC motor with metal gears. Which can give torque of 109Kgcm at 5amp.
I have attached a new motor driver board with ratings 5amp and 12 volts.

I got great help from article:- http://robosavvy.com/forum/viewtopic.php?t=2673
Thanks to all
Here is a video link: http://www.youtube.com/watch?v=q5HAL9QI59Q
Now I am testing the load capabilities

Statistics: Posted by MOHIT JINDAL — Mon May 20, 2013 6:44 am

How Ax12+ detect Over-load ?

2013-05-13T13:18:30+01:00

Well' I got confused in the commands. So I decided to use Usb2dynamixel and Dynamixel Wizard. I disable the Alarm LED and Alarm Shutdown to 0.
Then power off and On. Its on 0 now. Will it be there forever ? I want to shutdown ovrload trigger permanently.
Now in the Roboplus manager; the temperature is 69 red mark. and the red led is ON forever. I think now the problem is temperature is over. How to turn off the temp trigger ?
I think overload problem is solved now the temperature problem is left with LED still ON. Any idea

Statistics: Posted by MOHIT JINDAL — Mon May 13, 2013 1:18 pm

How Ax12+ detect Over-load ?

2013-05-10T18:34:14+01:00

See my cheat-sheet at http://robosavvy.com/Builders/Fritzoid/commands.zip

You can send commands in hexadecimal to dynamixels using the H command in manage mode. You could also use TOSS mode and a program.

First try tracing the packet traffic generated from simple operations using the MONITOR command followed by one or more READ or DUMP commands. This will give you a feel for the send and receive packet format.

It is a good idea to disconnect all the servos except the one you are working on too!!!!

Statistics: Posted by Fritzoid — Fri May 10, 2013 6:34 pm

How Ax12+ detect Over-load ?

2013-05-10T16:33:52+01:00

Ok. Where to use those commands ? In terminal ?
Anyone tried it ?
I am new to roboplus terminal.

Statistics: Posted by MOHIT JINDAL — Fri May 10, 2013 4:33 pm

How Ax12+ detect Over-load ?

2013-05-10T16:13:32+01:00

Mohit,

There is a "super secret" servo command called SYSTEM_WRITE (code 0x0D). It can write to any address in the EEPROM. The packet should look something like this...

0x0D, 0xF0, 0x55, 0x0F, 0xAA, offset, byte

...where 0x0D is the command code 0xF0550FAA is an authorization code, 'offset' is the EEPROM offset and 'byte' is the single byte of data to be written. As usual, you will need a 0xFFFF header and a termination checksum to complete the packet.

You may also want to look into DIGITAL_RESET (code 0x07) which can re-initialize the EEPROM to the factory defaults. Very useful for the case where you mess up using the above command.

Statistics: Posted by Fritzoid — Fri May 10, 2013 4:13 pm

How Ax12+ detect Over-load ?

2013-05-10T13:10:52+01:00

Hi; I want to know How to clear the Bit 5 of 0x12 ? That is the Overload trigger. I want to shutdown the overload trigger. Yes; I am ready to burn 1 Ax12+ because I am experimenting on it. Please help. You can read Ax12 Manual page 11 and 12 for details about Bit 5 and overload error.

Statistics: Posted by MOHIT JINDAL — Fri May 10, 2013 1:10 pm

How Ax12+ detect Over-load ?

2012-08-09T12:36:33+01:00

MOHIT wrote

Ok so the AX12+ has .bin file inside Atmega 8A chip ?

You could say that.

Statistics: Posted by Fritzoid — Thu Aug 09, 2012 12:36 pm

how to turn off overload detection

2012-08-09T07:19:51+01:00

how to turn off overload detection??

Regards,
Selva
http://www.chennaipackersmovers.com/ban ... movers.php

Statistics: Posted by selva — Thu Aug 09, 2012 7:19 am

How Ax12+ detect Over-load ?

2012-08-09T03:42:38+01:00

Ok so the AX12+ has .bin file inside Atmega 8A chip ?

Statistics: Posted by MOHIT JINDAL — Thu Aug 09, 2012 3:42 am

How Ax12+ detect Over-load ?

2012-08-08T20:45:31+01:00

What runs in the AVR or any computer is machine code, which contains binary instructions specific to the processor.

A compiler takes the source code in c or some other high-level language and converts it to assembler and then into machine code which is linked together with other machine code to create a binary image. The final result can be written to a .bin file if you like.

A bin file is essentially a dump of processor memory. However, it does not contain any information about what part of memory this dump corresponds to. Also, because it is binary it cannot be viewed or edited with a text editor. For this and other reasons Intel created the .hex format.

A .hex file is an ASCII representation of the binary image with location information included. It is much easier to work with and to transfer between machines.

Now to get your binary image into the flash memory of the AVR you need to use software (the boot loader) or hardware (an ISP). If you have an ISP you can usually use either a .bin or a .hex file.

If you go the software route then you'll need a program that can tell the boot loader where and how much data to write. Plus the actual bytes, of course. Fortunately Robotis has included this functionality in the Terminal application for you, but it expects to see a hex file as input. Other downloading programs prefer .hex files too. This is why most people output a hex file from the linkage editor.

So the .bin file is closest to what runs on the AVR but it's not as useful for downloading as the .hex file. The AVR has no use for the source code (.c) at all.

Statistics: Posted by Fritzoid — Wed Aug 08, 2012 8:45 pm

How Ax12+ detect Over-load ?

2012-08-08T17:30:25+01:00

hmmm.... Ok. Which file runs inside atmega 8a ? .bin or .hex or .c

Statistics: Posted by MOHIT JINDAL — Wed Aug 08, 2012 5:30 pm

How Ax12+ detect Over-load ?

2012-08-08T12:28:52+01:00

There is no load-sensing device, just a position sensor. The load is calculated as a function of distance from the target and time.

In order to build your own servo you would need a motor, a processor, a position sensor, an H-bridge, bearings, a gear train, and some interfacing hardware just for starters.

Gather the parts and then compare your costs to that of a commercial servo.

Statistics: Posted by Fritzoid — Wed Aug 08, 2012 12:28 pm

How Ax12+ detect Over-load ?

2012-08-08T03:22:05+01:00

Thanks but you say "ctlTorqueOn is true and ctlTorqueLimit and ctlCCWLimit are both non-zero. " These commands\functions won't work without any load sensing device. potentiometer sense the load or any other tiny thing inside the AX12+ chip ?

If I burn http://actuated.wordpress.com/ax12firmware/ into a new Atmega 8A chip. Can I make my own Servo motor ?

Statistics: Posted by MOHIT JINDAL — Wed Aug 08, 2012 3:22 am

How Ax12+ detect Over-load ?

2012-08-07T19:16:45+01:00

The source file answers all your questions.

Overload is set when the field PhysicalTorque exceeds one-half the control table value ctlTorqLimit. PhysicalTorque is an internally maintained field calculated within the routine.

Furthermore, overload is only recognized if the control table value ctlTorqueOn is true and ctlTorqueLimit and ctlCCWLimit are both non-zero.

Of course the overload limit is in place to protect the servo and possibly your fingers from destruction. Disabling this feature is NOT recommended.

You cannot read the servo firmware directly without a JTAG interface. You could, however, trace the download of a firmware upgrade and save that to a file. In either case you would then have to convert the hex file to assembler and eventually translate that to c, something like AX-12.c.

Statistics: Posted by Fritzoid — Tue Aug 07, 2012 7:16 pm