Robobuilder firmware 2.34

[PedroR]

Hi all

Robobuilder has made available Firmware version 2.34 on their Korean website but it is not yet available on the English Website.

We managed to get a copy of v.2.34 and uploaded it to our server.
It can be downloaded here http://robosavvy.com/RoboSavvyPages/Rob ... BC2.34.zip

From what we read on the Korean website (and with the help of Google Translate)the changelog for the new version can be found bellow.

Between 2.30 (the latest available on the English Robobuilder website) and 2.34 there was an interim release (2.31). I'm including the changelog for all of them as 2.31 seems to have made some change in the RBC protocol.

Control Box firmware version is 2.34.

(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)

<Different>;
- The default position Runtime remove unnecessary movement
- Failed to download files of a certain size motion to remove the problem


Control Box firmware version is 2.31.
(cumulative and included in 2.34)

(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)

<Different>;
- Motion Run command should not send a response packet upon receiving (1: N communication intended to eliminate the interference).


Control Box firmware version 2.30.
(this version is available on the English Robobuilder website; these features are also cumulative and included in v2.34)

<What>;

- Get Up Automatically (Should have "Acceleration sensor" installed RBC)

: In order to Enter or Exit this mode, press IR remoe button "# + STOP" button together.

You can see PF1 LED is blinking when this mode is entered.


- Continuous Walk: Keep Walking Forward or BackWard function
(This command works when user use Bluetooth Module or PC Communication Cable.)

* This function is NOT supported by IR remote controller.



? Caution
1) If this firmware does not work, please change with the previous firmware.


After the firmware upgrade it _may_ be necessary to perform any (or all) of the following procedures:
(DO NOT perform these procedures unless absolutely necessary; usually these are NOT necessary but we're posting them just for User's Reference).
1) Register the Remote Control on the RBC box.
2) Set the platform mode (press and hold the PF button to set it tot he correct Robot shape).
3) Reset the zero point
You should reffer to the User's Manual as it explains how to perform all of these procedures in detail should you need to do them.


Regards
Pedro.

[l3v3rz]

This is now on the official site

http://robobuilder.net/eng/

Wish they would provide documentation as to whats changed etc ...

[nicolas gomez]

Hi Pedro!!

I see in the Robobuilder/Firmware/LiPo the version RBC82.56_11.1V.zip
you have more info about this?

thanks
nicolas

Hi all

Robobuilder has made available Firmware version 2.34 on their Korean website but it is not yet available on the English Website.

We managed to get a copy of v.2.34 and uploaded it to our server.
It can be downloaded here http://robosavvy.com/RoboSavvyPages/Rob ... BC2.34.zip

From what we read on the Korean website (and with the help of Google Translate)the changelog for the new version can be found bellow.

Between 2.30 (the latest available on the English Robobuilder website) and 2.34 there was an interim release (2.31). I'm including the changelog for all of them as 2.31 seems to have made some change in the RBC protocol.

Control Box firmware version is 2.34.

(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)

<Different>;
- The default position Runtime remove unnecessary movement
- Failed to download files of a certain size motion to remove the problem


Control Box firmware version is 2.31.
(cumulative and included in 2.34)

(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)

<Different>;
- Motion Run command should not send a response packet upon receiving (1: N communication intended to eliminate the interference).


Control Box firmware version 2.30.
(this version is available on the English Robobuilder website; these features are also cumulative and included in v2.34)

<What>;

- Get Up Automatically (Should have "Acceleration sensor" installed RBC)

: In order to Enter or Exit this mode, press IR remoe button "# + STOP" button together.

You can see PF1 LED is blinking when this mode is entered.


- Continuous Walk: Keep Walking Forward or BackWard function
(This command works when user use Bluetooth Module or PC Communication Cable.)

* This function is NOT supported by IR remote controller.



? Caution
1) If this firmware does not work, please change with the previous firmware.


After the firmware upgrade it _may_ be necessary to perform any (or all) of the following procedures:
(DO NOT perform these procedures unless absolutely necessary; usually these are NOT necessary but we're posting them just for User's Reference).
1) Register the Remote Control on the RBC box.
2) Set the platform mode (press and hold the PF button to set it tot he correct Robot shape).
3) Reset the zero point
You should reffer to the User's Manual as it explains how to perform all of these procedures in detail should you need to do them.


Regards
Pedro.

[PedroR]

The information about the Firmware versions for users with LiPo is usually kept in a separate thread here http://robosavvy.com/forum/viewtopic.php?t=3660#33697

You can check there for more information.


In the case of RBC82.56_11.1V.zip I don't have much detailed information.
I just received the file from Robobuilder and posted it for our users to download.

Regards
Pedro

[Kondo]

Hello PedroR

I submitted a document root of your Robosavvy original, I translated into Spanish, and works great the new firmware.

http://www.limoncellodigital.com/2012/0 ... tivar.html

Regards