Legacy Forum: Preserving Nearly 20 Years of Community History - A Time Capsule of Discussions, Memories, and Shared Experiences.

RCB-1 download cable

KHR-1, KHR-2HV, KHR-3HV, ICS servos, RCB controllers and other Kondo products
4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1

RCB-1 download cable

Post by biz » Thu Dec 14, 2006 1:25 am

Post by biz
Thu Dec 14, 2006 1:25 am

I think i have some problem with the RS232 serial cable for KHR-1. My fren lost it b4 passing it to me.......Is there any schematic available so that i can build another one?
thanks
I think i have some problem with the RS232 serial cable for KHR-1. My fren lost it b4 passing it to me.......Is there any schematic available so that i can build another one?
thanks
biz
Robot Builder
Robot Builder
User avatar
Posts: 8
Joined: Tue Dec 12, 2006 1:00 am
Top

Post by limor » Thu Dec 14, 2006 2:34 am

Post by limor
Thu Dec 14, 2006 2:34 am

a bit of searching throuh past posts and i came by this one: http://robosavvy.com/Forums&file=viewtopic&t=29
a bit of searching throuh past posts and i came by this one: http://robosavvy.com/Forums&file=viewtopic&t=29
limor
Savvy Roboteer
Savvy Roboteer
User avatar
Posts: 1845
Joined: Mon Oct 11, 2004 1:00 am
Location: London, UK
Top

Post by biz » Thu Dec 14, 2006 3:34 am

Post by biz
Thu Dec 14, 2006 3:34 am

er....thanks for the link, but still not much info on that.
The only info i for the Serial RS232 cable is that its just normal connection with the Tx and Rx pin from the serial port to the board with resistor(unknown resistance) in serial with one of the signal pin.
Can i hv a more clearer picture on it?I mean the actual connection which can be plugged into the PCb-1 board pins.
Which pin of the board goes to which pin of the serial port.....
Thanks.
er....thanks for the link, but still not much info on that.
The only info i for the Serial RS232 cable is that its just normal connection with the Tx and Rx pin from the serial port to the board with resistor(unknown resistance) in serial with one of the signal pin.
Can i hv a more clearer picture on it?I mean the actual connection which can be plugged into the PCb-1 board pins.
Which pin of the board goes to which pin of the serial port.....
Thanks.
biz
Robot Builder
Robot Builder
User avatar
Posts: 8
Joined: Tue Dec 12, 2006 1:00 am
Top

Post by C-roy » Mon Dec 18, 2006 9:48 pm

Post by C-roy
Mon Dec 18, 2006 9:48 pm

kondo kagaku ics - pc interface2 serial cable
pin 2 white
pin 3 red
pin 5 black
resister is red red red gold and seems smaller than a 1/4 watt
resister goes from pin 2 to pin 4
there is also a jumper from pin 7 to pin 8
kondo kagaku ics - pc interface2 serial cable
pin 2 white
pin 3 red
pin 5 black
resister is red red red gold and seems smaller than a 1/4 watt
resister goes from pin 2 to pin 4
there is also a jumper from pin 7 to pin 8
C-roy
Newbie
Newbie
User avatar
Posts: 2
Joined: Tue Oct 24, 2006 1:00 am
Top

4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1
Return to KHR-1, KHR-2HV, KHR3-HV & Kondo