Legacy Forum: Preserving Nearly 20 Years of Community History - A Time Capsule of Discussions, Memories, and Shared Experiences.

Error 26 on Robonova...

Hitec robotics including ROBONOVA humanoid, HSR-8498HB servos, MR C-3024 Controllers and RoboBasic
4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1

Error 26 on Robonova...

Post by Sazabi » Mon Jan 07, 2008 9:14 am

Post by Sazabi
Mon Jan 07, 2008 9:14 am

Hello!
Trying to wright some data in my robo, but this error goes out and robo turns off, than turns on again.
Problem can appear in the beginning,in the middle or in the almost end of downloading.
Once i downloaded programme successfull,but only once.
Everything else works well, like controller info or realtime servo managment.
I use COM->USB translator, speed 115k.
is there any place to read about error codes?
Gonna try on PC with normal Serial port today,hope it will work
Hello!
Trying to wright some data in my robo, but this error goes out and robo turns off, than turns on again.
Problem can appear in the beginning,in the middle or in the almost end of downloading.
Once i downloaded programme successfull,but only once.
Everything else works well, like controller info or realtime servo managment.
I use COM->USB translator, speed 115k.
is there any place to read about error codes?
Gonna try on PC with normal Serial port today,hope it will work
Sazabi
Savvy Roboteer
Savvy Roboteer
Posts: 73
Joined: Mon Jan 07, 2008 8:57 am
Top

Post by i-Bot » Mon Jan 07, 2008 11:09 am

Post by i-Bot
Mon Jan 07, 2008 11:09 am

In the port setting window, did you try setting the communication over time slider to slow ?
In the port setting window, did you try setting the communication over time slider to slow ?
i-Bot
Savvy Roboteer
Savvy Roboteer
User avatar
Posts: 1142
Joined: Wed May 17, 2006 1:00 am
Top

Post by Sazabi » Mon Jan 07, 2008 3:01 pm

Post by Sazabi
Mon Jan 07, 2008 3:01 pm

Yeah,I did,doesn't help.
But now problem half-sold: i tried on PC with normall, build-in COM port(serial) and it works great.
But....feels like battery is low,cause robo moves only half a figure(
And my charger doesn't work on those plugs, where other electric stuff do. No idea why((
Yeah,I did,doesn't help.
But now problem half-sold: i tried on PC with normall, build-in COM port(serial) and it works great.
But....feels like battery is low,cause robo moves only half a figure(
And my charger doesn't work on those plugs, where other electric stuff do. No idea why((
Sazabi
Savvy Roboteer
Savvy Roboteer
Posts: 73
Joined: Mon Jan 07, 2008 8:57 am
Top

Post by Sazabi » Mon Jan 07, 2008 8:50 pm

Post by Sazabi
Mon Jan 07, 2008 8:50 pm

k, problem solved. the thing was in contacts of charger,inside it.they were kind melted,so i just cleaned em and it works well now.
But i still like to know error codes explanation:)
k, problem solved. the thing was in contacts of charger,inside it.they were kind melted,so i just cleaned em and it works well now.
But i still like to know error codes explanation:)
Sazabi
Savvy Roboteer
Savvy Roboteer
Posts: 73
Joined: Mon Jan 07, 2008 8:57 am
Top

4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1
Return to ROBONOVA-I & Hitec