Legacy Forum: Preserving Nearly 20 Years of Community History - A Time Capsule of Discussions, Memories, and Shared Experiences.

Error 8100

Bioloid robot kit from Korean company Robotis; CM5 controller block, AX12 servos..
4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1

Error 8100

Post by bergere » Thu Nov 29, 2007 10:25 pm

Post by bergere
Thu Nov 29, 2007 10:25 pm

Hello,

I have some problem with my Walking Droid.
I changed the firmware some times and after that it doesnt do anything.
I read in other topics how to handle with this problem.
Now my Walking Droid found just 4 Dynamixels ( The Motors ) but not my AX-S1. There is an Error. I changed my B-Rate to 1MBits but that doesnt change anything.

Error: 8100[0011:80] 100 002 027 001

I think its because he have a problem with the AX-S1 but i dont know how to repair it.

I hope you can help me.
Hello,

I have some problem with my Walking Droid.
I changed the firmware some times and after that it doesnt do anything.
I read in other topics how to handle with this problem.
Now my Walking Droid found just 4 Dynamixels ( The Motors ) but not my AX-S1. There is an Error. I changed my B-Rate to 1MBits but that doesnt change anything.

Error: 8100[0011:80] 100 002 027 001

I think its because he have a problem with the AX-S1 but i dont know how to repair it.

I hope you can help me.
Last edited by bergere on Wed Dec 19, 2007 7:07 am, edited 1 time in total.
bergere
Savvy Roboteer
Savvy Roboteer
Posts: 28
Joined: Thu Nov 29, 2007 10:18 pm
Top

Post by siempre.aprendiendo » Fri Nov 30, 2007 9:28 pm

Post by siempre.aprendiendo
Fri Nov 30, 2007 9:28 pm

Have you tested to connect only the AX-S1 to CM-5? May be is a problem with duplicated IDs...
Have you tested to connect only the AX-S1 to CM-5? May be is a problem with duplicated IDs...
Last edited by siempre.aprendiendo on Fri Nov 30, 2007 10:13 pm, edited 1 time in total.
siempre.aprendiendo
Savvy Roboteer
Savvy Roboteer
User avatar
Posts: 559
Joined: Wed Aug 08, 2007 9:13 pm
Location: Barcelona
Top

Post by bergere » Fri Nov 30, 2007 10:01 pm

Post by bergere
Fri Nov 30, 2007 10:01 pm

I will test this next time i am in office. Thank you.
I will test this next time i am in office. Thank you.
bergere
Savvy Roboteer
Savvy Roboteer
Posts: 28
Joined: Thu Nov 29, 2007 10:18 pm
Top

Post by bergere » Thu Dec 06, 2007 4:11 pm

Post by bergere
Thu Dec 06, 2007 4:11 pm

My mistake was that:
I changed the ID of the Sensor.
After that I tried to change ID back to 100.
But I changed all the ID.
So nothing works anymore.
But know i change all ID´s seperatly.


There is just one more problem.
He do not find the AX-S1. I take another AX-S1 and it works.
But he do not find the old one. So i can not change the ID back to 100?
What should i do? Is it destroyed?

Plz Help
My mistake was that:
I changed the ID of the Sensor.
After that I tried to change ID back to 100.
But I changed all the ID.
So nothing works anymore.
But know i change all ID´s seperatly.


There is just one more problem.
He do not find the AX-S1. I take another AX-S1 and it works.
But he do not find the old one. So i can not change the ID back to 100?
What should i do? Is it destroyed?

Plz Help
bergere
Savvy Roboteer
Savvy Roboteer
Posts: 28
Joined: Thu Nov 29, 2007 10:18 pm
Top

4 posts • Page 1 of 1
Post a reply
4 posts • Page 1 of 1
Return to Bioloid & Robotis